XGIMI Projectors

H2/H1/Z6

Note: H1–“Power” button — “Play” button

How to force-flash the system firmware:
1) Download the firmware to the root directory of an external USB device; (make sure the USB supports FAT32 format);
2) Connect the USB to the projector’s USB port (2.0);
3) Power off the device, long-press the “Power” button on the projector for 3-5 seconds until the fan emits a loud sound;
4) Please wait for the upgrade to complete.

ATV force flashing portable products (when force-flashing portable products, ensure that the battery power is greater than or equal to 50% and that it is connected to a power supply).
1. Download the firmware from the above link to your USB disk (Note: It should be USB 2.0 and supports FAT32 format)
2. Download the firmware to the root directory/folder on your USB disk.
3. Turn off your projector and plug in the power adapter.
4. Connect your USB disk to the projector.
5. Long-press the “-” & “+” buttons on the projector at the same time for 5-8 seconds, and release them when you hear the fan emit a loud sound.
6. You’ll see an Android robot and progress bar.
7. Please wait until the system has finished updating.

Z4 Aurora:
How to force-flash the system firmware:
1) Download the firmware to the root directory of an external USB device; (make sure the USB supports FAT32 format);
2) Connect the USB to the projector’s USB port (2.0);
3) Go to “Settings” – “About” – “System Update” – “USB Update”.
4) Please wait for the upgrade to complete.

Z4 Air:
How to force-flash the system firmware:
1) Download the firmware to the root directory of an external USB device; (make sure the USB supports FAT32 format);
2) Turn off your Z4 Air. Then plug in the power adapter, and connect your USB to the projector’s USB (2.0) port;
3) Long-press the power button on the back of Z4 Air, and slide the lens cap at the same time. Release the power button once the fan emits a loud sound.
4) Please wait for the upgrade to complete (Also, don’t unplug the power adapter during the update).

CC:
1) Turn off CC, close the lens cap, and unplug the power adapter.
2) Download the firmware to the root directory of your USB; (make sure the USB supports FAT32 format);
Note: You don’t need to create a new file clip.
3) Connect your USB to the projector’s USB 2.0 port.
4) Plug in the power adapter.
5) Open the lens cap and press the “+” and “-” buttons on the projector at the same time for around 3-5s. Release both when the fan emits a loud sound.
6) Wait for the update

（2）CC USB强刷升级方法二（镜头盖关闭状态）
① 下载USB强刷包GIMI_087B_MONET_WMP.bin并拷贝至U盘根目录；
② 将U盘插入机器的USB接口，插上电源；
③ 同时按住CC机身的“上一曲+下一曲”键；
④ 打开镜头盖，等待3-5s，即可松开，等待刷机完成。

Dear customer,

Thanks for choosing XGIMI!
The minimum & max projected size of long throw projectors：40” – 200”
Product included: HORIZON Series, Halo Series, MoGo Series, Elfin

The minimum & max projected size of short throw projector: 60” – 120”
Product included: AURA,

depending on your actual needs.
However, we suggest using the projection sizes below for the best viewing experience:

MoGo (210 ANSI lumens): 60-120 inches
MoGo Pro (300 ANSI lumens): 60-120 inches
MoGo Pro+ (300 ANSI lumens): 60-120 inches
Halo (800 ANSI lumens): 60-120 inches
Halo+ (900 ANSI lumens): 60-120 inches
Elfin (800 ANSI lumens): 60-120 inches
H2 (1350 ANSI lumens): 60-120 inches
HORIZON & HORIZON Pro (2200 ANSI lumens): 60-150 inches
AURA (2400 ANSI lumens): 80-120 inches

Image ratio: 16:9

Diagnoal size:
38 inches@1m (1.8m*0.5m); 76 inches@2m (1.7m&0.9m); 114 inches@3m (2.5m*1.4m);
151 inches@4m (3.4m*1.9m); 189 inches@5m (4.1m*2.4m); 227 inches@6m (5m*2.8m)